12-04-2018, 12:17 PM | #1 |
Lieutenant General
18663
Rep 14,108
Posts
Drives: G82 M4C X-Drive
Join Date: Mar 2013
Location: Orange County, CA
|
REX stopped turning on after coding
I used Bimmercode to turn on the REx manually (after 75%), but I've noticed that when my range gets low, the REx does NOT turn on by itself anymore. Anyone else encounter this?
I'm wondering if it was this setting: Range Extender activation battery level Available in KOMBI FPK_I12, KOMBI_I01_F56
__________________
2022 G82///M4 Competition X-Drive - KW-HAS, EBC Bluestuff, Millway Race Camber Plates, Cup2 Connect*, PSI High Flow Midpipe, Lightweight Front Lip, M Perf Flow Through Wing Previous • 2018 F80 ///M3 CS • 2016 F80 ///M3 IG: Raging_G82 |
12-04-2018, 01:13 PM | #2 | |
Colonel
1163
Rep 2,561
Posts |
Quote:
Alter Range Extender activation battery capacity level: 3000 ->SOC_HOLD_POS werte = hex value xx Units are 0.5% -- default = 0C which is 6% ie. 18 = 12% If you had accidentally set it to a lower value, or 0, that would produce the outcome you are describing. a
__________________
'19 TM3P (BK/BK)
'15 F80 M3 (SO/SS) ex-'17 I01 i3-BEV (PB/DD), ex-'15 I01 i3-REX, ex-E90, E46, E36's, E30's |
|
Appreciate
0
|
12-04-2018, 01:23 PM | #3 | ||
Lieutenant General
18663
Rep 14,108
Posts
Drives: G82 M4C X-Drive
Join Date: Mar 2013
Location: Orange County, CA
|
Quote:
__________________
2022 G82///M4 Competition X-Drive - KW-HAS, EBC Bluestuff, Millway Race Camber Plates, Cup2 Connect*, PSI High Flow Midpipe, Lightweight Front Lip, M Perf Flow Through Wing Previous • 2018 F80 ///M3 CS • 2016 F80 ///M3 IG: Raging_G82 |
||
Appreciate
0
|
12-05-2018, 11:17 PM | #4 | ||
Lieutenant General
18663
Rep 14,108
Posts
Drives: G82 M4C X-Drive
Join Date: Mar 2013
Location: Orange County, CA
|
Quote:
__________________
2022 G82///M4 Competition X-Drive - KW-HAS, EBC Bluestuff, Millway Race Camber Plates, Cup2 Connect*, PSI High Flow Midpipe, Lightweight Front Lip, M Perf Flow Through Wing Previous • 2018 F80 ///M3 CS • 2016 F80 ///M3 IG: Raging_G82 |
||
Appreciate
0
|
12-09-2018, 02:44 PM | #5 |
Enlisted Member
15
Rep 47
Posts |
I used bimmercode to change mine to 12% but it didn't work either. The little pointer is sitting at 12% on the SOC gauge but the REX doesn't start. I haven't let the charge get back down to 6% but I expect that it will start then. Seems that we can't change this value with bimmercode.
|
Appreciate
1
jmg18663.00 |
12-12-2018, 06:35 PM | #6 | |
Lieutenant General
18663
Rep 14,108
Posts
Drives: G82 M4C X-Drive
Join Date: Mar 2013
Location: Orange County, CA
|
Quote:
__________________
2022 G82///M4 Competition X-Drive - KW-HAS, EBC Bluestuff, Millway Race Camber Plates, Cup2 Connect*, PSI High Flow Midpipe, Lightweight Front Lip, M Perf Flow Through Wing Previous • 2018 F80 ///M3 CS • 2016 F80 ///M3 IG: Raging_G82 |
|
Appreciate
0
|
Post Reply |
Bookmarks |
|
|